CASIO EDIFICE 5123 MANUAL PDF

This watch does not have a city code that corresponds to the UTC offset of 3. About This Manual Button operations are indicated using the letters A through D shown in the illustration. Things to check before using the watch 1. Hold down C for about two seconds to enter the Timekeeping Mode, and then observe the movement of the x Second Hand. Is the x Second Hand moving smoothly at one-second intervals?

Author:Gugrel Gosar
Country:Malawi
Language:English (Spanish)
Genre:Art
Published (Last):18 January 2005
Pages:271
PDF File Size:10.6 Mb
ePub File Size:13.66 Mb
ISBN:121-6-41553-817-5
Downloads:62591
Price:Free* [*Free Regsitration Required]
Uploader:Vobei



This watch does not have a city code that corresponds to the UTC offset of 3. About This Manual Button operations are indicated using the letters A through D shown in the illustration. Things to check before using the watch 1. Hold down C for about two seconds to enter the Timekeeping Mode, and then observe the movement of the x Second Hand.

Is the x Second Hand moving smoothly at one-second intervals? Is the x Second Hand moving at two-second intervals or is it stopped completely? Go to step 2. The watch is charged sufciently. For details about charging, see Charging the Watch. Power is low. Charge the watch by placing it in a location where it is exposed to light. For details, see Charging the Watch. Use the procedure under To congure Home City settings to congure your Home City and daylight saving time settings.

Make sure these settings are congured correctly. Set the current time. The watch is now ready for use. Charging the Watch The face of the watch is a solar cell that generates power from light. The generated power charges a built-in rechargeable battery, which powers watch operations. The watch charges whenever it is exposed to light. Charging Guide Whenever you are not wearing the watch, be sure to leave it in a location where it is exposed to light.

Best charging performance is achieved by exposing the watch to light that is as strong as possible. When wearing the watch, makes sure that its face is not blocked from light by the sleeve of your clothing. The watch may enter a sleep state if its face is blocked by your sleeve even only partially. Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become particularly hot when exposed to the following conditions for long periods. On the dashboard of a car parked in direct sunlight Too close to an incandescent lamp Under direct sunlight Important!

Keep the watch in an area normally exposed to bright light when storing it for long periods. This helps to ensure that power does not run down. Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is blocked from exposure to light can cause power to run down. Make sure that the watch is exposed to bright light whenever possible. Power Levels You can get an idea of the watchs power level by observing the movement of the x Second Hand in the Timekeeping Mode.

If the x Second Hand is moving normally at one-second intervals, power is at Level 1. If the x Second Hand is moving at two-second intervals, power is at Level 2, which is quite low. Expose the watch to light as soon as possible so it can charge. Moving at two-second intervals. All functions enabled. Beeper disabled. All functions disabled. When power drops to Level 3, all functions will be disabled but the watch will continue to keep time internally for about one week. If you recharge the battery sufciently during this period, the analog hands will move automatically to the correct setting and regular timekeeping will resume.

After one week, all settings including timekeeping will be cleared. Recharging the battery will reset all settings to their initial factory defaults. Power Recovery Mode The watch is designed to go into a power recovery mode that stops hand operation temporarily whenever power suddenly drops below a certain level due to overuse of the alarm tone over a short period.

Note that all operations are disabled while the watch is in the power recovery mode. The hands will move to the correct positions and the watch will resume normal operation after power recovers in about 15 minutes. Putting the watch in a location where it is exposed to light will help power to recover sooner. Actual exposure times depend on lighting conditions. For details about the operating time and daily operating conditions, see the Power Supply section of the Specications. Power Saving Power Saving enters a sleep state automatically whenever the watch is left for a certain period in an area where it is dark.

The table below shows how watch functions are affected by Power Saving. There actually are two sleep state levels: second hand sleep and function sleep. Elapsed Time in Dark Operation 60 to 70 minutes second hand sleep x Second Hand only is stopped at 12 oclock, all other functions are enabled. The watch will not enter a sleep state between AM and PM.

If the watch is already in a sleep state when AM arrives, however, it will remain in the sleep state. The watch will not enter a sleep state while it is in the Stopwatch Mode. To recover from the sleep state Move the watch to a well-lit area or press any button. Mode Reference Guide Your watch has four modes. The mode you should select depends on what you want to do. To determine the watchs current mode Check the position of the n Right Dial Hand as shown under To select a mode.

To return to the Timekeeping Mode from any other mode Hold down C for about two seconds until the watch beeps twice. The n Right Dial Hand indicates the currently selected mode. The hand points to 0. The hand points to ALM. C Timekeeping Use the Timekeeping Mode to view the current time and date. To enter the Timekeeping Mode from any other mode, hold down C for about two seconds. To congure Home City settings Note This watch does not have a city code that corresponds to Newfoundland.

In the Timekeeping Mode, keep 1. A depressed for about ve seconds as the x Second Hand moves to the city code of the currently selected Home City. This indicates the city code setting mode. The watch will exit the setting mode automatically if you do not perform any operation for about two or three minutes.

For details about city codes, see the City Code Table. To change the Home City setting, press 2. D to move the x Second Hand clockwise. Keep pressing D until the x Second Hand is pointing at the city code you want to select as your Home City.

Do not perform the next operation until these hands stop moving. Press 3. After the setting is the way you want, press 4. A to return to the Timekeeping Mode. To toggle the Home City time between standard time and daylight saving time Perform the step 1 under To congure Home City settings.

Press 2. After the setting is the way you want, press 3. Coordinated Universal Time, the world-wide scientic standard of timekeeping. To change the current time setting In the Timekeeping Mode, keep 1. For details about these settings, see steps 2 and 3 under To congure Home City settings. In the following steps, each press of C cycles between settings as shown below. The watch will beep, and the x Second Hand and n Right Dial Hand will move to their 12 oclock positions.

This is the time setting mode. Use 4. Each press of either button will move the hands z Hour Hand and c Minute Hand one minute. To stop high-speed hand movement, press any button. When setting the time, make sure that the v Upper Left Dial Hand indicates the proper a. If you want to change the date setting at this time, press C and perform the procedure starting from step 3 under To change the current date setting. After the time setting is the way you want, press 5.

This will cause the x Second Hand to move automatically to 12 oclock and resume movement from there. To change the current date setting In the Timekeeping Mode, keep 1. C twice. The watch will beep and change to the year setting mode. The year can be set in the range of to

NAVAGRAHA ASHTOTTARA SHATANAMAVALI IN PDF

Cheap casio edifice 5123 manual deals

Quick Links. This watch does not have a city code that corresponds to the UTC offset of —3. Things to check before using the watch. Hold down C for about two seconds to enter the Timekeeping Mode, and. Is the x Second Hand moving smoothly at one-second intervals? Power is low.

INDUMATHI NOVELS PDF

Edifice EQS-500 User Manual / Casio Module 5123

.

Related Articles