ASTM F594 PDF

Historical Version s - view previous versions of standard. Work Item s - proposed revisions of this standard. More F This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance. Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: Group 1; Group 2; Group 3; Group 4; Group 5; Group 6; and Group 7.

Author:Juzil Mijas
Country:Norway
Language:English (Spanish)
Genre:Health and Food
Published (Last):18 July 2008
Pages:251
PDF File Size:18.42 Mb
ePub File Size:5.66 Mb
ISBN:828-6-31700-544-8
Downloads:24503
Price:Free* [*Free Regsitration Required]
Uploader:Faujas



Historical Version s - view previous versions of standard. Work Item s - proposed revisions of this standard. More F This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance. Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: Group 1; Group 2; Group 3; Group 4; Group 5; Group 6; and Group 7.

The finished fasteners shall meet the applicable mechanical properties. Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F and shall be of the same alloy group.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Scope 1. Alloys A. Condition B. Link to Active This link will always route to the current Active version of the standard.

KRYPTOGRAFIA DLA PRAKTYKOW PDF

ASTM F594 Nuts

The specification of the ASTM F Nuts takes several alloys that are intended for applications that require corrosion resistance in general. The ASTM F Hex Nuts specification takes into consideration twelve austenitic grades, two ferritic grades, four martensitic grades and one precipitation hardening grade of stainless steel. These alloys have been specified in cold worked, age-hardened, hardened and tempered conditions. F Stainless Steel Washers usually have properties that are dependent on the grade of stainless steel used. For instance, ASTM F Stainless Steel Nuts manufactured from ferritic grade of stainless steel are magnetic, tough and have fairly good corrosion resistance. But ASTM F specification produced from austenitic grade of stainless steels have a high tensile strength, good ductility, good resistance to corrosion resistance and are non-magnetic in nature.

MAGNIWORK MANUAL PDF

ASTM F594 Fasteners

An extensive portfolio that covers all aspects and requirements of the industry, providing quality products that can be used in confidence. These nuts are for general purpose usage, and are available in seven alloy groups. A number of other less common grades of ASTM F exist, but are not detailed in the description below. The Mechanical table here is limited to Alloy groups 1 and 2, as those are the most common and the Chemical table is only showing the most common alloy grades used for their respective alloy groups. The main reason being we have an excellent warehousing and storage facilities for both finished and semi finished goods.

Related Articles